For each level of doors you can set whether the hardware is on the top, middle or bottom. In this window you can change from a knob, pull or no hardware. Clicking this button will open another window where you can change the locations for the hardware if needed. The cabinet editing window has a Door Hardware button for cabinets with doors. This can be individually adjusted for each cabinet. In each of the Upper, Base and Tall standards windows, enter the location the hardware should be placed on the doors. The Pull size is the diameter of the pull. In the Set All Other Standards window enter the Knob diameter, Pull size and length and whether you want knobs or pulls on the doors and drawers. To add hardware to the elevation view of the cabinets a few standards must first be set. If you wish to print your elevations in black and white, un-check the Color On box in the selection window. The Add To Custom Colors button is not supported by the program. Click the OK button and your color will be saved. Also, you may type the values you want in the six number boxes on the right. Then click on the arrow on the right to adjust the color further. To adjust the colors in the custom color window, left click on the large color box and slide your mouse around until you find a color close to what you want.
![shelf and cabinet planner shelf and cabinet planner](https://image.made-in-china.com/43f34j00jaKGBVUWHvoz/Wall-Children-Kids-Design-in-Bookshelf-Cabinet-Wooden.jpg)
You may choose one of the these basic colors or click the Define Custom Colors> button to fine tune your color.
#Shelf and cabinet planner full
Sides will be kept full depth.Ĭlick the file menu and select Set Elevation ColorsĪ selection window will open, click the OK button next to the item you wish to adjust the color for. Leaving this box blank will plan the cabinets normally.Įntering Zero in this box will make the program deduct the thickness of the backs from the side, tops, bottoms and partitions.Įntering a value greater than Zero will make the program deduct that amount from the tops, bottoms and partitions. The size entered here will be added the depth of the cabinet sides. Side to face frame dado depth-This is for people who dado their face frames to the cabinet box. If you wish to edit a list before printing it, send it to the main window then when done editing it, press the print list buttonĪrched doors-The top box is for the width of the top rail and the second box is for the height of the arch.
![shelf and cabinet planner shelf and cabinet planner](https://www.wgwoodproducts.com/wp-content/uploads/2020/07/DES-1a-768x1024.jpg)
When calculating Master lists- These two check boxes tell the program what to do with the master lists when calculating them. Tenon length for face frames- The size entered in this box will be doubled and add to all appropriate face frame sizes Entering 'X' will give you decimals only. If they are an exact fraction, then that fraction will be given down to 1/32. Entering 'N' will have the program give exact sizes.
![shelf and cabinet planner shelf and cabinet planner](https://cdn.homedit.com/wp-content/uploads/2018/10/Open-shelving-hooks-underneath-819x1024.jpg)
Round to nearest 1/16- Entering 'Y' will tell the program to trim sizes to the nearest 1/16. Tenon length for doors-The size entered in this box is doubled and added to all door and raised panel rails and middle rails or stiles where appropriate Shelf edge thickness- amount to deduct from overall shelf depthĭeduct for shelf length- lets you set how much is deducted from adjustable shelf's lengthĭeduct for shelf depth- lets you set how much is deducted from adjustable shelf's depthĭoor stile and rail cutter depth- This size is used to figure how much to add to the rails of doors. This works only when planning a lob from left to right.Ĭlick & Drag- Checking this box will keep the click & drag feature enabled. Location assist- Checking this box will fill in the location box with the location + the width of the last saved cabinet in a job. Rabbet depth for sides-This is how much the front and back is rabbeted into the sides of the drawer box.ĭado depth for bottoms-This is how much the bottoms are dadoed into the sides, fronts and backs of the drawer boxes. This setting will let you adjust the height of base cabinet partitions to allow for stretchers to run above them without having to cut a notch for them.ĭeduct for width-This is how much to deduct from the drawer opening for figuring the overall width of the drawer box.ĭeduct for height-This is how much to deduct from the drawer opening for figuring the height of the drawer box.ĭeduct for depth-This is how much is deducted from the cabinet depth for figuring drawer box depth.
![shelf and cabinet planner shelf and cabinet planner](https://sc04.alicdn.com/kf/Hfe2524918943429e9b6c4ef2e8fc7b907.jpg)
The size entered in this box on the base cabinet standards window will be applied to all base cabinets, vanities, and tall cabinets.
#Shelf and cabinet planner windows
The size entered in this box on the upper cabinet standards windows will be applied to all upper cabinets. The size you enter in this box is the amount that the bottom rail sticks up above the bottom of the cabinet. If you set scribe to a side of the cabinet, the program will only shorten the box by that amount.Entering 2 will run the bottom through on sides with scribe applied to them and shorten that sides length by the amount of the bottom rail minus the bottom lip size. Entering 1 in this box will plan upper cabinets with the top and bottom of equal lengths.